-40%

Soft Start 1000W D.I.Y.

$ 7.38

Availability: 106 in stock
  • Number of Channels: 1
  • Type: Soft Start
  • All returns accepted: ReturnsNotAccepted
  • Brand: Unbranded
  • MPN: Does Not Apply
  • Country/Region of Manufacture: Serbia
  • Condition: New
  • Model: Soft Start 1000w

    Description

    The delay is intended to switch on the mains to heavy loads gradually to ensure that the switch-on current
    remains within certain limits and to prevent the fuses from blowing. The elements that cause high currents
    at switch-on are, for instance, the electrolytic capacitors in the power supply of an output amplifier.
    Since these are not charged at switch-on, they constitute a virtual short-circuit on the supply lines. The
    current can, however, be kept within limits by inserting the present delay circuit between the mains outlet
    and the transformer primary. The amplifier is then powered in two stages:
    in the first instance, the current is limited by a number of heavy-duty series resistors a second later these
    resistors are shunted (short-circuited) by a relay contact.
    In the diagram, R4–R7 are the heavy-duty series resistors, each with a value of 10 ohm and rated at 5 W.
    They limit the switch-on current to about 5.5 A. After relay close, the 230VAC PCB rail is ready for 2000w
    continuous.
    The relay is a type whose contact is rated at 2000 VA, which will be sufficient in most cases. Its supply is
    derived directly from the mains via potential divider R3-C1-B1-relay coil. The resistor, R3 limits the current
    at switch-on, after which C1 limits the current in normal operation to about 20 mA. The delay time is
    determined by electrolytic capacitors C2 and C3 in parallel with the relay. The delay time may be altered by
    suitably changing the value of one or both of these capacitors.
    For safety’s sake, the board also has provision for a mains fuse, F1. The rating of this depends, of course, on
    the current drawn by the load. It should be noted that in the case of a double-mono stereo output amplifier
    (with separate power supplies) each of the mono amplifiers must be given a mains-on delay.
    Note that C1 is a metallized paper type, wich is designed specially for mains voltage applications and meets
    stringent regulatory requirements. Finally, at all times bear in mind that the circuit is connected to the mains,
    so do not touch anything inside the unit during operation and make sure that all wiring is safe and secure.
    Kit is built with high quality components such as Omron Relay and Uni ohm resistors.
    Dimensions are 6.5x7.0 cm
    Shipping Address &
    Combined Shipping
    We ship to confirmed addresses. If there is a different address that you would like to have the item shipped to, please let us know.  When you buy multiple items, we will do combine shipment and. If send us an email or message, we will respond in 24 hours.
    Shipping Time
    We ship the item next day after the payment has been received. If there is a delay in the shipment, we will notify the buyer immediately. We use Regular air mail or Priority Mail depending on the item purchased.
    Delivery Time
    Delivery times are different depending on the shipment method. Priority mail takes approximately 2-3 days . The delivery time is up to the post office.
    Returns/Exchange
    We accept exchange/returns within 14 days of customer receiving the item. Buyers pay the return shipping. Item must be sent back in original condition for exchange or return. For returns on products that are unwanted, there is a 20% restocking fee for the item. Please message us or email us in regards to returns/exchanges.
    Feedbacks
    We really appreciate every positive feedback if you can kindly leave for us . If for some reason, you are unsatisfied with our service; please contact us and please know that we highly value our customers and work my hardest to provide the best service and product.
    Payment
    Immediate payment through Paypal